With the technological evolutionary advent, a vision-based approach presents the remote measuring approach for the analysis of vibration. The structure vibration test and model parameter identification in the detection of the structure of the bridge evaluation occupies the important position. The bridge structure to operate safely and reliably is ensured, according to the geological data of qixiashan lead-zinc mine and engineering actual situation, with the aid of international mining software Surpac. To build the 3D visualization model of the (...) application of visualization in mine production are discussed. The results show that the final solid model of -425 stope can accurately display the spatial form of each layer of stope through rotation, amplification and movement. The proposed system is effectually able to perform cutting, volume calculation and roaming in any direction, which has certain guiding significance for mine production management. An accuracy value of 98.75%, the sensitivity of 99%, specificity of 99.64% and PPV of 99.89% are achieved using the proposed 3D modelling and visualization algorithm for vibration signal processing and management. (shrink)

There is a growing demand for information and computational technology for surgeons help with surgical planning as well as prosthetics design. The two-dimensional images are registered to the three-dimensional (3D) model for high efficiency. To reconstruct the 3D model of knee joint including bone structure and main soft tissue structure, the evaluation and analysis of sports injury and rehabilitation treatment are detailed in this study. Mimics 10.0 was used to reconstruct the bone structure, ligament, and meniscus according to (...) the pulse diffusion-weighted imaging sequence (PDWI) and stir sequences of magnetic resonance imaging (MRI). Excluding congenital malformations and diseases of the skeletal muscle system, MRI scanning was performed on bilateral knee joints. Proton weighted sequence (PDWI sequence) and stir pulse sequence were selected for MRI. The models were imported into Geomagic Studio 11 software for refinement and modification, and 3D registration of bone structure and main soft tissue structure was performed to construct a digital model of knee joint bone structure and accessory cartilage and ligament structure. The 3D knee joint model including bone, meniscus, and collateral ligament was established. Reconstruction and image registration based on mimics and Geomagic Studio can build a 3D model of knee joint with satisfactory morphology, which can meet the requirements of teaching, motion simulation, and biomechanical analysis. (shrink)

For VR systems, one of its core parts is to present people with a real and immersive 3D simulation environment. This paper uses real-time computer graphics technology, three-dimensional modeling technology, and binocular stereo vision technology to study the multivisual animation character objects in virtual reality technology; designs a binocular stereo vision animation system; designs and produces a three-dimensional model; and develops a virtual multivisual animation scene application. The main research content and work performed in the text include the research (...) of the basic graphics rendering pipeline process and the analysis and research of each stage of the rendering pipeline. It mainly analyzes the 3D graphics algorithm used in the three-dimensional geometric transformation of computer graphics and studies the basic texture technology, basic lighting model, and other image output processes used in the fragment processing stage. Combined with the development needs of the subject, the principles of 3D animation rendering production software and 3D graphics modeling are studied, and the solid 3D model displayed in the virtual reality scene is designed and produced. This article also reflects the application of virtual reality in multivisual animation character design from the side, so it has realistic value and application prospects. (shrink)

The Global Workspace Theory and Information Integration Theory are two of the most currently accepted consciousness models; however, these models do not address many aspects of conscious experience. We compare these models to our previously proposed consciousness model in which the thalamus fills-in processed sensory information from corticothalamic feedback loops within a proposed 3D default space, resulting in the recreation of the internal and external worlds within the mind. This 3D default space is composed of all cells of the (...) body, which communicate via gap junctions and electrical potentials to create this unified space. We use 3D llustrations to explain how both visual and non-visual sensory information may be filled-in within this dynamic space, creating a unified seamless conscious experience. This neural sensory memory space is likely generated by baseline neural oscillatory activity from the default mode network, other salient networks, brainstem, and reticular activating system. (shrink)

In this paper, we develop a 3D-individual-based model to understand effect of various small-scale mechanisms in phytoplankton cells, on the cellular aggregation process. These mechanisms are: spatial interactions between cells due to their chemosensory abilities, a molecular diffusion and a demographical process. The latter is considered as a branching process with a density-dependent death rate to take into account the local competition on resources. We implement the IBM and simulate various scenarios under real parameter values for phytoplankton cells. To (...) quantify the effects of the different processes quoted above on the spatial and temporal distribution of phytoplankton, we used two spatial statistics: the Clark–Evans index and the group belonging percentage. Our simulation study highlights the role of the branching process with a weak-to-medium competition in reinforcing the aggregating structure that forms from attraction mechanisms, and shows by contrast that aggregations cannot form when competition is high. (shrink)

This is a proceedings based on the talk that was made in the workshop “Black Holes, Gravitational Waves and Spacetime Singularities” at Vatican Observatory on 9–12 May 2017. Since then we have constructed some corrections, hence this paper includes them. Here we employ the \\)D Kitaev superconductor model and perform the Wilsonian renormalization group transformation in a real space. We regard the running energy scale or the repetition number of RG transformation as a new emergent direction of the spacetime, (...) thus constructing a one dimensional higher spacetime. The solution for the beta function is plugged into the effective action and then the RG information is encoded in the curvature of the emergent spacetime. We found that there are two fixed points in which one corresponds to the Lifshitz spacetime with the dynamical critical exponent \ and the other fixed point corresponds to the AdS\ spacetime. The topological superconducting phase induces a naked singularity in the spacetime and the trivial superconducting phase produces regular spacetime. Except the fixed points, each parameter phase shows spatial anisotropic spacetime description as it goes to IR limit. (shrink)

The 3D Prandtl fluid flow through a bidirectional extending surface is analytically investigated. Cattaneo–Christov fluid model is employed to govern the heat and mass flux during fluid motion. The Prandtl fluid motion is mathematically modeled using the law of conservations of mass, momentum, and energy. The set of coupled nonlinear PDEs is converted to ODEs by employing appropriate similarity relations. The system of coupled ODEs is analytically solved using the well-established mathematical technique of HAM. The impacts of various physical (...) parameters over the fluid state variables are investigated by displaying their corresponding plots. The augmenting Prandtl parameter enhances the fluid velocity and reduces the temperature and concentration of the fluid. The momentum boundary layer boosts while the thermal boundary layer mitigates with the rising elastic parameter strength. Furthermore, the enhancing thermal relaxation parameter ) reduces the temperature distribution, whereas the augmenting concentration parameter drops the strength of the concentration profile. The increasing Prandtl parameter declines the fluid temperature while the augmenting Schmidt number drops the fluid concentration. The comparison of the HAM technique with the numerical solution shows an excellent agreement and hence ascertains the accuracy of the applied analytical technique. This work finds applications in numerous fields involving the flow of non-Newtonian fluids. (shrink)

Hopfield neural network is considered as an artificial model derived from the brain structures and it is an important model that admits an adequate performance in neurocomputing. In this article, we solve a dynamical model of 3D HNNs via Atangana–Baleanu fractional derivatives. To find the numerical solution of the considered dynamical model, the well-known Predictor-Corrector method is used. A number of cases are taken by using two different sets of values of the activation gradient of the (...) neurons as well as six different initial conditions. The given results have been perfectly established using the different fractional-order values on the given derivative operator. The objective of this research is to investigate the dynamics of the proposed HNN model at various values of fractional orders. Nonlocal characteristic of the AB derivative contains the memory in the system which is the main motivation behind the proposal of this research. (shrink)

Recent technical improvements, such as 3D microscopy imaging, have shown the necessity of studying 3D biological tissue architecture during carcinogenesis. In the present paper a computer simulation model is developed allowing the visualization of the microscopic biological tissue architecture during the development of metaplastic and dysplastic lesions.The static part of the model allows the simulation of the normal, metaplastic and dysplastic architecture of an external epithelium. This model is associated to a knowledge base which contains only data (...) on the nasal epithelium. The latter has been well studied by numerous authors and its lesional states are well known. An inference engine allows the initialization of the static model parameters. A statistical comparison between simulated epithelia and real epithelia is achieved by adjusting the parameter values during the simulation. (shrink)

This thesis first introduces the basic principles of model-based image sequence coding technology, then discusses in detail the specific steps in various implementation algorithms, and proposes a basic feature point calibration required in three-dimensional motion and structure estimation. This is a simple and effective solution. Aiming at the monocular video image sequence obtained by only one camera, this paper introduces the 3D model of the sculpture building into the pose tracking framework to provide initial depth information. The whole (...) posture tracking framework can be divided into three parts, namely, the construction of the initial sculpture model, the posture tracking between frames, and the robustness processing during continuous tracking. In order to reduce the complexity of calculation, this paper proposes a new three-dimensional mesh model and a moving image restoration algorithm based on this model. At the same time, the influence of the intensity and direction factors in the scene is added, the simulation results are given, and the next step is discussed. The optimization work that needs to be done. (shrink)

This paper presents the intelligent virtual animals that inhabit Omosa, a virtual learning environment to help secondary school students learn how to conduct scientific inquiry and gain concepts from biology. Omosa supports multiple agents, including animals, plants, and human hunters, which live in groups of varying sizes and in a predator-prey relationship with other agent types (species). In this paper we present our generic agent architecture and the algorithms that drive all animals. We concentrate on two of our animals to (...) present how different parameter values affect their movements and inter/intra-group interactions. Two evaluations studies are included: one to demonstrate the effect of different components of our architecture; another to provide domain expert validation of the animal behavior. (shrink)

How can we improve business ethics education for the twenty first century? This study evaluates the effectiveness of a visual case exercise in the form of a 3D immersive game given to undergraduate students at two UK Universities as part of a mandatory business ethics module. We propose that due to evolving learning styles, the immersive nature of interactive games lends itself as a vehicle to make the learning of ethics more ‘concrete’ and ‘personal’ and therefore more engaging. To achieve (...) this, we designed and built an immersive 3D simulation game in the style of a visual case. The effectiveness of the game was evaluated using a mixed methods approach measuring recognised and adapted constructs from the technology acceptance model. Results demonstrate that students found the game beneficial to their learning of ethics with the development of knowledge and skills applicable to the real world and that they engaged with the process due to game elements. Findings demonstrate the potential for the development of simulated games to teach ethics at all levels and modes of delivery and the contribution of this type of visual case model as a pedagogic method. (shrink)

3D printing or additive manufacturing is a novel method of manufacturing parts directly from digital model using layer-by-layer material build-up approach. This tool-less manufacturing method can produce fully dense metallic parts in short time, with high precision. Features of additive manufacturing like freedom of part design, part complexity, light weighting, part consolidation, and design for function are garnering particular interests in metal additive manufacturing for aerospace, oil and gas, marine, and automobile applications. Powder bed fusion, in which each powder (...) bed layer is selectively fused using energy source like laser, is the most promising additive manufacturing technology that can be used for manufacturing small, low-volume, complex metallic parts. This review presents overview of 3D Printing technologies, materials, applications, advantages, disadvantages, challenges, economics, and applications of 3D metal printing technology, the DMLS process in detail, and also 3D metal printing perspectives in developing countries. (shrink)

As a result of the development of new technologies such as satellite communication, digitalization, and multimedia computer networks, new media such as blogs, online magazines, and wireless network media have sparked a lot of interest. This study uses 3D clothing display technologies to improve the customer experience of online clothing marketing, aid in the improvement of online clothing marketing efficacy, and extensively discuss the digital clothing anthropometric model. Furthermore, this study employs the convex hull approach and NURBS fitting technology (...) to address concerns with digital clothing anthropometric measurement and provides a practical solution for measuring straight line length, circumference length, and curve length. Furthermore, this research incorporates 3D intelligent technology to develop an online fitting system as well as an intelligent display system for garments. The simulation experiment investigation revealed that the smart clothing 3D display system proposed in this work has a substantial impact on growing online e-commerce clothing marketing as well as improving clothing marketing effectiveness. (shrink)

The book in front of you is the first international academic volume on the legal, philosophical and economic aspects of the rise of 3D printing. In recent years 3D printing has become a hot topic. Some claim that it will revolutionize production and mass consumption, enabling consumers to print anything from clothing, automobile parts and guns to various foods, medication and spare parts for their home appliances. This may significantly reduce our environmental footprint, but also offers potential for innovation and (...) creativity. At the same time 3D printing raises social, ethical, regulatory and legal questions. If individuals can print anything they want, how does this affect existing systems of intellectual property rights? What are the societal consequences of the various types of products one can print with a 3D printer, for example weapons? Should all aspects of 3D printing be regulated, and if so, how and to what ends? How will businesses (have to) change their way of working and their revenue model in light of the shift to printing-on-demand? How will the role of product designers change in a world where everyone has the potential to design their own products? These and other questions are addressed in high quality and in-depth contributions by academics and experts, bringing together a wide variety of academic discussions on 3D printing from different disciplines as well as presenting new views, broadening the discussion beyond the merely technical dimension of 3D printing. Bibi van den Berg is Associate Professor at eLaw, the Center for Law and Digital Technologies at Leiden University, The Netherlands. Simone van der Hof is Full Professor at eLaw in Leiden and Eleni Kosta is Associate Professor at TILT, the Tilburg Institute for Law, Technology and Society at Tilburg University, The Netherlands. (shrink)

A paradoxical attitude exists toward professional philosophy: philosophical inquiry is considered important and complex, but professionals are deemed irrelevant and unnecessary. This paradox doubly affects sport philosophy as evidenced by the field’s marginalization in higher education and sociopolitical discourse. To counter the sport philosophy paradox, I present a pragmatically oriented three-dimensional approach to inquiry that turns the field “inside-out”. A community of engaged, melioratively oriented sport philosophy inquirers in this 3D model collectively conducts theoretical, applied, and instrumental inquiry. Each (...) dimension is outlined in detail from a professional sport philosophy perspective, and implications are considered relative to the field’s future endeavors. (shrink)

Through the analysis of facial feature extraction technology, this paper designs a lightweight convolutional neural network. The LW-CNN model adopts a separable convolution structure, which can propose more accurate features with fewer parameters and can extract 3D feature points of a human face. In order to enhance the accuracy of feature extraction, a face detection method based on the inverted triangle structure is used to detect the face frame of the images in the training set before the model (...) extracts the features. Aiming at the problem that the feature extraction algorithm based on the difference criterion cannot effectively extract the discriminative information, the Generalized Multiple Maximum Dispersion Difference Criterion and the corresponding feature extraction algorithm are proposed. The algorithm uses the difference criterion instead of the entropy criterion to avoid the “small sample” problem, and the use of QR decomposition can extract more effective discriminative features for facial recognition, while also reducing the computational complexity of feature extraction. Compared with traditional feature extraction methods, GMMSD avoids the problem of “small samples” and does not require preprocessing steps on the samples; it uses QR decomposition to extract features from the original samples and retains the distribution characteristics of the original samples. According to different change matrices, GMMSD can evolve into different feature extraction algorithms, which shows the generalized characteristics of GMMSD. Experiments show that GMMSD can effectively extract facial identification features and improve the accuracy of facial recognition. (shrink)

Alzheimer's disease (AD) is the most common cause of dementia, and there is currently no cure. The “β‐amyloid cascade hypothesis” of AD is the basis of current understanding of AD pathogenesis and drug discovery. However, no AD models have fully validated this hypothesis. We recently developed a human stem cell culture model of AD by cultivating genetically modified human neural stem cells in a three‐dimensional (3D) cell culture system. These cells were able to recapitulate key events of AD pathology (...) including β‐amyloid plaques and neurofibrillary tangles. In this review, we will discuss the progress and current limitations of AD mouse models and human stem cell models as well as explore the breakthroughs of 3D cell culture systems. We will also share our perspective on the potential of dish models of neurodegenerative diseases for studying pathogenic cascades and therapeutic drug discovery. (shrink)

Science, technology, engineering, and mathematics disciplines commonly illustrate 3D relationships in diagrams, yet these are often challenging for students. Failing to understand diagrams can hinder success in STEM because scientific practice requires understanding and creating diagrammatic representations. We explore a new approach to improving student understanding of diagrams that convey 3D relations that is based on students generating their own predictive diagrams. Participants’ comprehension of 3D spatial diagrams was measured in a pre- and post-design where students selected the correct 2D (...) slice through 3D geologic block diagrams. Generating sketches that predicated the internal structure of a model led to greater improvement in diagram understanding than visualizing the interior of the model without sketching, or sketching the model without attempting to predict unseen spatial relations. In addition, we found a positive correlation between sketched diagram accuracy and improvement on the diagram comprehension measure. Results suggest that generating a predictive diagram facilitates students’ abilities to make inferences about spatial relationships in diagrams. Implications for use of sketching in supporting STEM learning are discussed. (shrink)

Because the traditional social media fuzzy static image interactive three-dimensional (3D) reconstruction method has the problem of poor reconstruction completeness and long reconstruction time, the social media fuzzy static image interactive 3D reconstruction method is proposed. For preprocessing the fuzzy static image of social media, the Harris corner detection method is used to extract the feature points of the preprocessed fuzzy static image of social media. According to the extraction results, the parameter estimation algorithm of contrast divergence is used to (...) learn the restricted Boltzmann machine (RBM) network model, and the RBM network model is divided into input, output, and hidden layers. By combining the RBM-based joint dictionary learning method and a sparse representation model, an interactive 3D reconstruction of fuzzy static images in social media is achieved. Experimental results based on the CAD software show that the proposed method has a reconstruction completeness of above 95% and the reconstruction time is less than 15 s, improving the completeness and efficiency of the reconstruction, effectively reconstructing the fuzzy static images in social media, and increasing the sense of reality of social media images. (shrink)

Motion pose capture technology can effectively solve the problem of difficulty in defining character motion in the process of 3D animation production and greatly reduce the workload of character motion control, thereby improving the efficiency of animation development and the fidelity of character motion. Motion gesture capture technology is widely used in virtual reality systems, virtual training grounds, and real-time tracking of the motion trajectories of general objects. This paper proposes an attitude estimation algorithm adapted to be embedded. The previous (...) centralized Kalman filter is divided into two-step Kalman filtering. According to the different characteristics of the sensors, they are processed separately to isolate the cross-influence between sensors. An adaptive adjustment method based on fuzzy logic is proposed. The acceleration, angular velocity, and geomagnetic field strength of the environment are used as the input of fuzzy logic to judge the motion state of the carrier and then adjust the covariance matrix of the filter. The adaptive adjustment of the sensor is converted to the recognition of the motion state. For the study of human motion posture capture, this paper designs a verification experiment based on the existing robotic arm in the laboratory. The experiment shows that the studied motion posture capture method has better performance. The human body motion gesture is designed for capturing experiments, and the capture results show that the obtained pose angle information can better restore the human body motion. A visual model of human motion posture capture was established, and after comparing and analyzing with the real situation, it was found that the simulation approach reproduced the motion process of human motion well. For the research of human motion recognition, this paper designs a two-classification model and human daily behaviors for experiments. Experiments show that the accuracy of the two-category human motion gesture capture and recognition has achieved good results. The experimental effect of SVC on the recognition of two classifications is excellent. In the case of using all optimization algorithms, the accuracy rate is higher than 90%, and the final recognition accuracy rate is also higher than 90%. In terms of recognition time, the time required for human motion gesture capture and recognition is less than 2 s. (shrink)

In three-dimensional (3D) computer graphics, photography is treated not as the final product but as data to be extracted, information to be mapped onto and raw material to augment 3D models. Texture maps, normal maps and bump maps, created from photographic data, describe the reflectance properties of an object in a virtual scene. They give instructions to the render engine to calculate the correct pixel value, generating a near imperceptibly natural scene for the human eye. Computer graphics utilizes a network (...) of images taken from different perspectives and at different scales to achieve photorealism. The project investigates one of many algorithmic visual systems that act as a backbone of virtual reality and gaming. (shrink)

Previous research has successfully used feature integration theory to operationalise the predictions of Perceptual Load Theory, while simultaneously testing the predictions of both models. Building on this work, we test the extent to which these models hold up in a 3D world. In two experiments, participants responded to a target stimulus within an array of shapes whose apparent depth was manipulated using a combination of monoscopic and stereoscopic cues. The search task was designed to test the predictions of feature integration (...) theory, as the target was identified by a single feature or a conjunction of features and embedded in search arrays of varying size, and perceptual load theory, as the task included congruent and incongruent distractors presented alongside search tasks imposing high or low perceptual load. Findings from both experiments upheld the predictions of feature integration theory, regardless of 2D/3D condition. Longer search times in conditions with a combination of monoscopic and stereoscopic depth cues suggests that binding features into three-dimensional objects requires greater attentional effort. This additional effort should have implications for perceptual load theory, yet our findings did not uphold its predictions; the effect of incongruent distractors did not differ between conjunction search trials and feature search trials. Individual differences in susceptibility to the effects of perceptual load were evident and likely explain the absence of load effects. Overall, our findings suggest that feature integration theory may be useful for predicting attentional performance in a 3D world. (shrink)

Mathematics from the electromagnetic field quantization procedure and the soliton models of photons are used to construct a new 3D model of photons. Besides the interaction potential between the charged particle and the photons, which contains the annihilation and creation operators of photons, the new function for a description of free propagating photons is derived. This function presents the vector potential of the field, the function is a product of the harmonic oscillator eigenfunction with the well-defined coordinate of the (...) oscillator and the Gaussian function of the polar radius in the transverse direction. In the article, the difference between the quantum mechanics of particles and photons is discussed. (shrink)

Anderson localization of electromagnetic waves in three-dimensional disordered dielectric structures is studied using a simple yet realistic theoretical model. An effective approach based on analysis of probability distributions, not averages, is developed. The disordered dielectric medium is modeled by a system of randomly distributed electric dipoles. Spectra of certain random matrices are investigated and the possibility of appearance of the continuous band of localized waves emerging in the limit of an infinite medium is indicated. It is shown that localization (...) could be achieved without tuning the frequency of monochromatic electromagnetic waves to match the internal (Mie-type) resonances of individual scatterers. A possible explanation for the lack of experimental evidence for strong localization in 3D as well as suggestions how to make localization experimentally feasible are also given. Rather peculiar requirements for setting in localization in 3D as compared to 2D are indicated. (shrink)

Two experiments were performed to explore the mechanisms of human 3D shape perception. In Experiment 1, the subjects’ performance in a shape constancy task in the presence of several cues (edges, binocular disparity, shading and texture) was tested. The results show that edges and binocular disparity, but not shading or texture, are important in 3D shape perception. Experiment 2 tested the effect of several simplicity constraints, such as symmetry and planarity on subjects’ performance in a shape constancy task. The 3D (...) shapes were represented by edges or vertices only. The results show that performance with or without binocular disparity is at chance level, unless the 3D shape is symmetric and/or its faces are planar. In both experiments, there was a correlation between the subjects’ performance with and without binocular disparity. Our study suggests that simplicity constraints, not depth cues, play the primary role in both monocular and binocular 3D shape perception. These results are consistent with our computational model of 3D shape recovery. (shrink)

The demand for integrating and sharing heterogeneous data online has attracted the interest of cultural institutions in making information access and retrieval more effective via Semantic Web technologies. The present study proposes a digital repository for 3D scans of modernist sculptures in public spaces in the city of Rio de Janeiro, Brazil, with a view to ensuring access, use, reuse and preservation of this information. This is a qualitative exploratory experimental study based on the scientific literature and specific empirical material. (...) It presents the analysis results of vocabularies for physical artifact documents and their digital counterparts on the Semantic Web and a discussion on how these align with the nature of the metadata determined here, as well as a metadata modeling prototype implemented on the Tainacan platform and aimed at cataloging digital 3D replicas. We claim that the proposed model for documenting cultural heritage assets on Tainacan is easy to implement, in that it uses accessible technology with a wide internet user base, highly expressive in its descriptions of 3D and multimedia content and based on well-established metadata and ontology standards recommended by regulatory bodies and communities such as the World Wide Web Consortium and International Organization for Standardization. Keywords: networked heritage documents, digital repositories, 3D digitization, semantic annotation. (shrink)

This paper establishes a model on the upstream and downstream relationship among private enterprises, provincial and local officials, and the central government in the real estate market using the population ecology theory of mutual relations among individual species from the perspective of business ecosystem. A dynamic model is introduced and the complex dynamical behaviors of such a predator-prey model are investigated by means of numerical simulation. The local stability conditions and complex dynamics are investigated, and the existence (...) of chaos is discussed in the sense of Marotto theorem; bifurcation diagrams, Lyapunov exponents, sensitivity analysis for initial values, and time history figure of the system are mapped out and discussed. This shows that there are two routes to complicated dynamics, one of which is the cascade of flip bifurcations resulting in periodic cycles, and the other one is Neimark-Sacker bifurcation which produces attractive invariant closed curves. We arrive at conclusions that the phenomenon of chaos is harmful to private enterprises, and unstable behavior is often unfavorable. Thus, linear feedback control is applied to drive the model to a stable state when the system exhibits chaotic behaviors, achieving the goal of eliminating the negative effects to a large extent. (shrink)

The widely accepted two-dimensional circumplex model of emotions posits that most instances of human emotional experience can be understood within the two general dimensions of valence and activation. Currently, this model is facing some criticism, because complex emotions in particular are hard to define within only these two general dimensions. The present theory-driven study introduces an innovative analytical approach working in a way other than the conventional, two-dimensional paradigm. The main goal was to map and project semantic emotion (...) space in terms of mutual positions of various emotion prototypical categories. Participants (N = 187; 54.5% females) judged 16 discrete emotions in terms of valence, intensity, controllability and utility. The results revealed that these four dimensional input measures were uncorrelated. This implies that valence, intensity, controllability and utility represented clearly different qualities of discrete emotions in the judgments of the participants. Based on this data, we constructed a 3D hypercube-projection and compared it with various two-dimensional projections. This contrasting enabled us to detect several sources of bias when working with the traditional, two-dimensional analytical approach. Contrasting two-dimensional and three-dimensional projections revealed that the 2D models provided biased insights about how emotions are conceptually related to one another along multiple dimensions. The results of the present study point out the reductionist nature of the two-dimensional paradigm in the psychological theory of emotions and challenge the widely accepted circumplex model. (shrink)

In traditional 3D reconstruction methods, using a single view to predict the 3D structure of an object is a very difficult task. This research mainly discusses human pose recognition and estimation based on 3D multiview basketball sports dataset. The convolutional neural network framework used in this research is VGG11, and the basketball dataset Image Net is used for pretraining. This research uses some modules of the VGG11 network. For different feature fusion methods, different modules of the VGG11 network are used (...) as the feature extraction network. In order to be efficient in computing and processing, the multilayer perceptron in the network model is implemented by a one-dimensional convolutional network. The input is a randomly sampled point set, and after a layer of perceptron, it outputs a feature set of n × 16. Then, the feature set is sent to two network branches, one is to continue to use the perceptron method to generate the feature set of n × 1024, and the other network is used to extract the local features of points. After the RGB basketball sports picture passes through the semantic segmentation network, a picture containing the target object is obtained, and the picture is input to the constructed feature fusion network model. After feature extraction is performed on the RGB image and the depth image, respectively, the RGB feature, the local feature of the point cloud, and the global feature are spliced and fused to form a feature vector of N × 1152. There are three branches for this vector network, which, respectively, predict the object position, rotation, and confidence. Among them, the feature dimensionality reduction is realized by one-dimensional convolution, and the activation function is the ReLU function. After removing the feature mapping module, the accuracy of VC-CNN_v1 dropped by 0.33% and the accuracy of VC-CNN_v2 dropped by 0.55%. It can be seen from the research results that the addition of the feature mapping module improves the recognition effect of the network to a certain extent. (shrink)

Additive manufacturing has spread widely over the past decade, especially with the availability of home 3D printers. In the future, many items may be manufactured at home, which raises two ethical issues. First, there are questions of safety. Our current safety regulations depend on centralized manufacturing assumptions; they will be difficult to enforce on this new model of manufacturing. Using current US law as an example, I argue that consumers are not capable of fully assessing all relevant risks and (...) thus continue to require protection; any regulation will likely apply to plans, however, not physical objects. Second, there are intellectual property issues. In combination with a 3D scanner, it is now possible to scan items and print copies; many items are not protected from this by current intellectual property laws. I argue that these laws are ethically sufficient. Patent exists to protect what is innovative; the rest is properly not protected. Intellectual property rests on the notion of creativity, but what counts as creative changes with the rise of new technologies. (shrink)

In this paper, to solve the problem of slow design of arts and crafts and to improve design efficiency and aesthetics, the existing big data and 3D technology are used to conduct an in-depth analysis of the optimization of the rapid design system of arts and crafts machine salt baking. In the system requirement analysis, the functional modules of this system are identified as nine functional modules such as design terminology management system and external information import function according to the (...) actual usage requirements. In the system design, the overall structure design, database design, and functional module design of the system are comprehensively elaborated, and the key issues such as 3D display and home layout generation algorithm based on reinforcement learning are analyzed and designed. In the implementation part of the system, the overall construction of the system and the composition of functional modules are introduced in detail and the main functional modules of the system are presented with interface diagrams. In the system implementation part, the overall system construction and functional module composition are introduced in detail, the main functional modules of the system are shown with interface diagrams, codes, and algorithms, and the specific implementation process of 3D display and soft layout algorithms are also explained in detail. The process of Surface Mount Technology big data processing and analysis is designed, and the design of SMT production line data collection scheme and real-time data processing architecture is completed. Based on the characteristics of SMT production line data, the K-means algorithm is used to detect data outliers and verify the accuracy of the method; also, the Spark-based association rule printing parameter recommendation model is designed, and the efficiency of the Apriori algorithm is significantly improved by parallelization. (shrink)

The structure of the deep artificial neural network is similar to the structure of the biological neural network, which can be well applied to the 3D visual image recognition of aerobics movements. A lot of results have been achieved by applying deep neural networks to the 3D visual image recognition of aerobics movements, but there are still many problems to be overcome. After analyzing the expression characteristics of the convolutional neural network model for the three-dimensional visual image characteristics of (...) aerobics, this paper builds a convolutional neural network model. The model is improved on the basis of the traditional model and unifies the process of aerobics 3D visual image segmentation, target feature extraction, and target recognition. The convolutional neural network and the deep neural network based on autoencoder are designed and applied to aerobics action 3D visual image test set for recognition and comparison. We improve the accuracy of network recognition by adjusting the configuration parameters in the network model. The experimental results show that compared with other simple models, the model based on the improved AdaBoost algorithm can improve the final result significantly when the accuracy of each model is average. Therefore, the method can improve the recognition accuracy when multiple neural network models with general accuracy are obtained, thereby avoiding the complicated parameter adjustment process to obtain a single optimal network model. (shrink)

A terahertz frequency-modulated continuous wave imaging radar system is developed for high-resolution 3D imaging recently. Aiming at the problems of long data acquisition periods and large sample sizes for the developed imaging system, an algorithm based on compressed sensing is proposed for THz FMCW radar 3D imaging in this paper. Firstly, the FMCW radar signal model is built, and the conventional range migration algorithm is introduced for THz FMCW radar imaging. Then, compressed sensing is extended for THz FMCW radar (...) 3D imaging, and the Newton smooth L0-norm algorithm is presented for sparse measurement data reconstruction. Both simulation and measurement experiments demonstrate the feasibility of reconstructing THz images from measurements even at the sparsity rate of 20%. (shrink)

Diffusion MRI is widely used to investigate neuronal and structural development of brain. dMRI data is often contaminated with various types of artifacts. Hence, artifact type identification in dMRI volumes is an essential pre-processing step prior to carrying out any further analysis. Manual artifact identification amongst a large pool of dMRI data is a highly labor-intensive task. Previous attempts at automating this process are often limited to a binary classification of the dMRI volumes or focus on detecting a single type (...) of artifact. In this work, we propose a deep learning-based automated multiclass artifact classifier for dMRI volumes. Our proposed framework operates in 2 steps. In the first step, the model predicts labels associated with 3D mutually exclusive collectively exhaustive sub-volumes or “slabs” extracted from whole dMRI volumes. In the second step, through a voting process, the model outputs the artifact class present in the whole volume under investigation. We used two different datasets for training and evaluating our model. Specifically, we utilized 2,494 poor-quality dMRI volumes from the Adolescent Brain Cognitive Development and 4,226 from the Healthy Brain Network dataset. Our results demonstrate accurate multiclass volume-level main artifact type prediction with 96.61 and 97.52% average accuracies on the ABCD and HBN test sets, respectively. Finally, in order to demonstrate the effectiveness of the proposed framework in dMRI pre-processing pipelines, we conducted a proof-of-concept dMRI analysis exploring the relationship between whole-brain fractional anisotropy and participant age, to test whether the use of our model improves the brain-age association. (shrink)

Background: Trait self-esteem reflects stable self-evaluation, and it affects social interaction patterns. However, whether and how trait self-esteem can be expressed through behaviors are controversial. Considering that facial expressions can effectively convey information related to personal traits, the present study investigated the three-dimensional facial movements related to self-esteem level and the sex differences therein. Methods: The sample comprised 238 participants. Their levels of trait self-esteem were evaluated by employing the Rosenberg Self-Esteem Scale. During self-introductions, their facial movements in 3D space (...) were recorded by Microsoft Kinect. Two-way ANOVA was performed to analyze the effect of self-esteem and gender on 3D facial movements. Additionally, Logistic regression models were established to describe the relationship between 3D facial movements and self-esteem levels in both genders. Results: The results of two-way ANOVA revealed a main effect of trait self-esteem level for cheeks and lips’ movements. Meanwhile, there was a significant interaction between trait self-esteem and gender on the variability of lips’ movements. In addition, the combination of facial movements can effectively identify trait self-esteem in men and women, with 75.5 and 68% accuracy, respectively. Conclusion: The present results suggest that the 3D facial expressions of individuals with different trait self-esteem levels were different, and such difference is affected by gender. Our study explores a possible way in which trait self-esteem plays a role in social interaction and also provides the basis for automatic self-esteem recognition. (shrink)

Just before the Scientific Revolution, there was a "Mathematical Revolution", heavily based on geometrical and machine diagrams. The "faculty of imagination" (now called scientific visualization) was developed to allow 3D understanding of planetary motion, human anatomy and the workings of machines. 1543 saw the publication of the heavily geometrical work of Copernicus and Vesalius, as well as the first Italian translation of Euclid.

Insect vision is nothing if not active. The regular head movements, called saccades, enable the fly Drosophila to keep a straight path in flight despite inequalities in the thrust of the wings. Using their own motion, bees in flight measure the ranges of nearby objects. A long history of research shows that bees discriminate visually in ways that depend on their activity or task, so we must distinguish between vision during flying, fixating or hovering and landing.Bees return again and again (...) for a reward of sugar solution and use their eyes to find their way. In an apparatus that makes them discriminate between two simulataneously visible but regularly interchanged targets, seen at a distance of 27 cm, bees are able to distinguish a remarkable number of simple patterns, but they fail in certain critical cases. The results can be explained with the hypothesis that bees have several broadly tuned overlapping filters with large fields that respond to the predominant orientation in a region of the image, and others for radial and circular patterns. Together with colour, these filters are independent of range. Bees prefer to use landmarks where they can, then global pattern at the largest scale, and lastly the detail around the goal. The way that discrimination of one visual feature is independent of other variables can be explained by models analogous to the colour triangle in colour discrimination. (shrink)

The technology, which is implemented with cross platform tools, is proposed for modeling of gesture units of sign language, animation between states of gesture units with a combination of gestures. Implemented technology simulates sequence of gestures using virtual spatial hand model and performs recognition of dactyl items from camera input using trained on collected training dataset set convolutional neural network, based on the MobileNetv3 architecture, and with the optimal configuration of layers and network parameters. On the collected test dataset (...) accuracy of over 98% is achieved. (shrink)

This paper exploits the modified simple equation and dynamical system schemes to integrate the Klein–Gordon model amid quadratic nonlinearity arising in nonlinear optics, quantum theories, and solid state physics. By implementing the modified simple equation technique, we develop some disguise adaptation of analytical solutions in terms of hyperbolic, exponential, and trigonometric functions with some special parameters. We apply the dynamical system to bifurcate the model and draw distinct phase portraits on unlike parametric constraints. Following each orbit of all (...) phase portraits, we originate bounded and unbounded solitary, periodic, and periodic rogue-type wave solutions of the KG model. These two schemes extract widespread classes of solitary, periodic, and periodic rogue-type wave solutions for the KG model jointly due to restrictions on parameters. We also analyze the effect of parameters on the obtained wave solutions and discuss why and when it changes its nature. We illustrate some dynamical features of the acquired solutions via the 3D, 2D, and contour graphics. (shrink)